Rubber & Plastic Products

Iron-Pillared Clay Raises Oil Yield in Automotive Plastic Waste Pyrolysis

A study finds that iron-modified bentonite lifts liquid yields from end-of-life vehicle plastics, though the resulting oil still falls short of diesel specifications in density and viscosity.

Bram OosterhuisOctober 14, 20265 min read3 views
A cutaway concept illustration of a pyrolysis reactor processing shredded automotive plastic parts, with oil and vapour passing through a bed of clay catalyst.

Recovering plastics from end-of-life vehicles is increasingly seen as a way to improve resource recovery, and pyrolysis — the thermal decomposition of polymers at elevated temperatures in the absence of oxygen — has emerged as a promising route for turning waste polymers into fuels and chemicals. A new study examines how plastics taken directly from vehicle components behave during thermal and catalytic pyrolysis, and how an iron-modified clay catalyst changes the outcome.

Previous work on automotive plastics has largely focused on automotive shredder residue, a heterogeneous mix of plastics, metals, textiles and other materials. Less is known about plastics recovered directly from parts such as dashboards, bumpers and headlamps, which can carry mineral fillers, flame retardants, fiberglass and other additives that influence how the material degrades and what products form.

Feedstock taken from real components

Rather than working with mixed shredder residue, the researchers characterised plastics recovered directly from end-of-life vehicles. The feedstock contained acrylonitrile butadiene styrene (ABS), high-density and low-density polyethylene (HDPE and LDPE), polypropylene (PP), polystyrene (PS) and fiberglass, along with substantial volatile and ash fractions. Front and rear bumpers accounted for 86.6% of the sample by weight, and the fiberglass commonly used to reinforce automotive components contributed to the relatively high ash content.

An iron-pillared clay catalyst

Catalysts can improve pyrolysis by accelerating reactions, shifting product distributions and potentially lowering the temperature or residence time needed. Commercial zeolites have been widely studied, but lower-cost clay-based alternatives are attracting interest. Among these, pillared clays modified with metals such as iron, titanium or zirconium have shown potential to raise liquid yields and influence the formation of fuel-range hydrocarbons; iron-modified clays are especially appealing because they may improve oil production without relying on more expensive commercial catalysts.

In this study, the team modified bentonite clay through iron pillaring rather than using it in its original form. The process introduces iron species into the clay structure, altering characteristics such as surface acidity and pore structure that can affect pyrolysis reactions. The work also addressed a gap in earlier research by characterising the automotive plastic waste before pyrolysis rather than after.

Yield moves, composition less so

The team compared thermal and catalytic pyrolysis across temperatures from roughly 350°C to 521°C and catalyst loadings of about 6% to 34% by weight, using a statistical experimental design to evaluate the interaction between temperature and catalyst concentration.

The catalyst strongly affected liquid yield. Catalytic pyrolysis produced an average oil yield of about 68%, compared with 41% for thermal pyrolysis alone. The highest oil yield, 78.6%, was reached at approximately 416°C with a catalyst loading of about 24%. By contrast, the catalyst had much less influence on the composition of the oil. Thermal and catalytic runs produced similar proportions of hydrocarbons in the C8 to C24 range associated with gasoline- and diesel-range compounds, meaning the catalyst helped convert more feedstock into liquid but did not substantially shift that liquid toward a higher share of diesel-range molecules.

Temperature proved the stronger lever on product composition. Lower pyrolysis temperatures favoured diesel-range organics, while temperatures above 450°C produced a heavier, waxier oil.

Fuel properties fall short in places

Several properties of the resulting oil were comparable to commercial diesel. The researchers reported a calorific value of 49.85 MJ/kg, a flash point of 113°C and total aromatics of 3.55% by area — values within or comparable to ranges specified for conventional fuels, they noted. Branched heptenes and heptanes dominated the oil, compounds also identified in earlier studies of polypropylene and automotive-plastic pyrolysis.

Not all properties met diesel specifications, however. Both density and viscosity exceeded the limits typically specified for diesel fuel, which the researchers attributed in part to heavier, long-chain hydrocarbon fractions remaining in the oil. Additional processing could therefore be required before the oil can serve as a diesel-range fuel. The team suggested approaches including distillation and centrifugation, as well as optimising reaction conditions through lower temperatures and longer residence times, to reduce heavier fractions and improve fuel properties.

What comes next

The study positions pyrolysis as a technically promising way to recover value from automotive plastics, while making clear that further development is needed before broader commercial application. Future work could investigate different iron concentrations in the catalyst, improve reactor designs and heat transfer, and combine pyrolysis with downstream distillation to separate gasoline- and diesel-range fractions.

Better collection and sorting of automotive plastics will also matter. Without systematic removal and classification of plastic components from end-of-life vehicles, reliable data on the volume and composition of available automotive plastic waste remain limited. More information on these waste streams would help researchers and recyclers assess feedstock availability and plan potential industrial-scale pyrolysis operations.